Recently Weiwa Machinery completed the shipment of a horizontal carbonization furnace to one of the leading briquette manufacturers in Lebanon. This making charcoal machine was carefully inspected, test-run in our workshop, and then packed for ocean freight to Beirut.
Shipment Process of the Horizontal Carbonization Furnace to Lebanon
The exported unit is a rail-mounted horizontal carbonization furnace with a stainless steel inner tank and a fully integrated smoke purification system. Before departure our technicians ran a no-load trial at approximately 350 °C to verify the thermocouple accuracy, door sealing performance, and gas recirculation function. The furnace body, trolley, chimney, and purification tower were wrapped in anti-rust film, strapped, and loaded into a 20 ft container. All fittings such as the pressure gauge, sealing cap, and combustion chamber baffle were double checked. For briquette manufacturers in Lebanon who plan to carbonize both lump wood and pre-formed briquettes, this model offers the flexibility to switch raw materials without hardware modification.
How the Horizontal Carbonization Furnace Works to Make Charcoal from Wood
To make charcoal from wood or biomass in a horizontal chamber, the process follows three thermodynamic stages. First, the loaded trolley is pushed into the horizontal barrel and the door is sealed with high-temperature rock wool gasket. External fire or electric heating raises the inner temperature to 120–180 °C, driving off surface moisture from the wood logs, cây tre , hoặc vỏ dừa. Second, as temperature climbs to 250–350 °C under limited oxygen, pyrolysis begins and volatile matters are released. These gases pass through the purification unit where tar and condensates are separated; the cleaned combustible gas is then ducted back to the burner and reignited to sustain the furnace temperature near 500–600 °C, which greatly reduces external fuel consumption. Third, after 6–10 hours depending on batch size and moisture content, the heating stops and the unit cools naturally or with assisted airflow until the inner temperature drops below 50 °C before the charcoal is unloaded.
Raw Materials Suitable for This Charcoal Making Machine
Our making charcoal machine accepts hardwood logs, branch wood, cây tre , vỏ dừa, vỏ hạt cọ, lõi ngô, and sawdust briquettes that have already been extruded by a charcoal briquette machine. Fine sawdust or rice husk must be compressed into briquettes before being placed in the furnace, otherwise they may block the smoke channels. This versatility is one reason why Lebanese customers looking for a charcoal making machine for sale in Lebanon often choose the Weiwa horizontal model as the core of their charcoal briquette production line.
Why Lebanon Is a Growing Market for Charcoal Briquette Production
Lebanon has abundant agricultural residues and wood offcuts from furniture workshops in the Mount Lebanon and Bekaa regions. With rising energy costs and periodic fuel shortages, many local entrepreneurs are turning to charcoal briquette production as both an income source and a way to provide affordable cooking fuel. Importing a reliable charcoal making machine for sale in Lebanon allows processors to convert low-cost biomass into high fixed-carbon charcoal for BBQ, Shisha, và sưởi ấm công nghiệp. Moreover, environmental regulations increasingly favor smokeless carbonization technologies that recover and reuse pyrolysis gas, which is exactly what the Weiwa horizontal carbonization furnace delivers.
Challenges Faced by Briquette Manufacturers in Lebanon
Local briquette manufacturers in Lebanon often struggle with inconsistent raw material size, high moisture in freshly cut wood, and the lack of after-sales support from overseas suppliers. Weiwa Machinery addresses these pain points by supplying adjustable trolley racks for mixed-size loads, recommending pre-drying solutions, and providing English & Arabic operation manuals plus remote video guidance for installation and first trial run.
On-Site Trial Run Feedback from the Lebanese Customer
Upon arrival and installation the customer conducted a trial batch using mixed hardwood logs and previously formed sawdust briquettes. The furnace reached carbonization temperature in approximately 3.5 hours thanks to the gas recirculation system. The resulting charcoal showed uniform black coloration, low ash content, and a fixed carbon rate exceeding 78 percent. Smoke emission during the entire cycle was minimal and the purification tower captured visible tar effectively. The customer confirmed the machine meets their expected daily throughput for charcoal briquette production and plans to add a second unit in the next purchasing season. Such field validation reinforces why more briquette manufacturers in Lebanon inquire about our charcoal making machine for sale in Lebanon each quarter.
Integrating the Horizontal Furnace into a Complete Charcoal Briquette Production Line
While the horizontal carbonization furnace produces premium lump charcoal, many businesses in Lebanon further process part of the output into uniform briquettes. A typical line includes a crusher to grind charcoal pieces, a wheel mixer to blend charcoal powder with a small amount of binder and water, a charcoal briquette extruder machine or hydraulic press to shape the mix, and finally a mesh belt dryer. The lump charcoal from our furnace can also be sold directly to restaurants and hookah lounges. Whether your goal is to make charcoal from wood for lump sales or to feed a charcoal briquette production plant, the Weiwa horizontal furnace adapts easily. You can view the specifications of our Lò cacbon hóa ngang and compare models suited to different batch capacities.
Why Choose Weiwa Machinery as Your Charcoal Making Machine Supplier?
Công ty sản xuất máy móc Henan Weiwa, Ltd. is a dedicated making charcoal machine and biomass recycling equipment factory based in Zhengzhou, Trung Quốc. We stock standard models ranging from 500 kg to 3 ton per batch, offer customization on trolley size and combustion chamber, and hold CE certification for major markets. Our export experience covers more than 130 countries including Lebanon, Ai Cập, Algeria, Indonesia, and Vietnam. Each charcoal making machine for sale in Lebanon is load-tested before leaving the factory and comes with a one-year warranty plus lifetime technical consultation. For briquette manufacturers in Lebanon seeking stable equipment, spare parts availability, and responsive support, Weiwa Machinery aims to be a long-term partner rather than a one-time vendor.
Frequently Asked Questions About Charcoal Making Machine for Lebanon
Can the horizontal furnace carbonize coconut shell and sawdust briquette together?
Đúng, as long as the sawdust has been compressed into dense briquettes. Coconut shells may require slightly longer carbonization time due to their thickness, but the temperature control system accommodates both in a single batch if loaded evenly on the trolley.
What fuel is needed to start the carbonization process?
Initial heating can be done with firewood, than đá, or LPG depending on local availability. Once pyrolysis gas is generated and purified, the system runs primarily on its own recovered gas, lowering ongoing fuel cost for charcoal briquette production.
Do you provide installation service in Lebanon?
We offer detailed installation videos, English/Arabic manuals, and remote video assistance. On-site engineer dispatch is available upon request; the customer covers round-trip airfare, accommodation, and local transport.
If you are evaluating a charcoal making machine for sale in Lebanon or want to learn more about how to make charcoal from wood and biomass with our horizontal carbonization furnace, please contact our sales team today for a tailored quotation and production flow chart.
Contact Weiwa Machinery:
Đám đông / WhatsApp: +86 138 3809 3177
E-mail: info@cjlmachinegroup.com
WeChat
+8613838093177
